dishes and microtitre plates to conical flasks.
 Features:
• Max. load capacity is 7.5kg(O330) and 2.5kg(O180) with platform
• Double LCDs for independent display of time and speed
• Used with a wide variety of accessories
• Maintenance- free brushless DC motor
• Over speed detection and protection
• Remote function provide PC control and data transmission
  DLAB orbital and linear shakers are ideal for almost any vessel from microcentrifuge tubes through petri
dishes and microtitre plates to conical flasks.
 Features:
• Max. load capacity is 7.5kg(O330) and 2.5kg(O180) with platform
• Double LCDs for independent display of time and speed
• Used with a wide variety of accessories
• Maintenance- free brushless DC motor
• Over speed detection and protection
• Remote function provide PC control and data transmission
Â
PEEK is a high temperature resistant thermoplastic, with high glass transition temperature (143℃) and melting point (334℃), load heat deformation temperature up to 316℃ (30% glass fiber or carbon fiber reinforced grade)
PEEK is widely used in petroleum, food processing, automobile, aerospace and other fields with its excellent electrical properties, mechanical properties, high temperature resistance, corrosion resistance and so on.
PEEK film
0.3- 1 mm, 20-600 - mm wide
PEEK rods
Model and color of PEEK rod:
1, PEEK5600G (brown gray/earth yellow) using pure polyether ether ketone resin as raw material manufacturing, in all PEEK levels of good toughness, good impact resistance. PEEK can be sterilized by convenient disinfection methods (steam, drying heat, ethanol and Y-ray), and the raw materials of PEEK meet the requirements of the European Union and the United States FDA for food suitability. These characteristics make it very popular in the medical, pharmaceutical and food processing industries.
2, PEeK-5600LF30 (black) add PTFE, graphite and carbon fiber results, make
Peek-5600lf30 becomes bearing grade plastic. Its superior friction properties (low friction coefficient, wear resistance, high peak pressure limit) make this grade an ideal material for friction applications.
3, PEEK-5600GF30 (brown gray) the material filled with 30% glass fiber reinforced plastic, has better rigidity and creep resistance than PEEK5600G, as well as better dimensional stability, the manufacturing of structural parts is ideal. It can withstand fixed load for a long time at high temperature. If the PEEK-5600GF30 is used as a sliding part, its adaptability should be carefully checked because the glass fiber scratches the mating surface.
4, PEeK-5600CF30 (black) The material filled with 30% carbon fiber reinforced, has better mechanical properties than PeeK-5600GF30 (higher elastic modulus, mechanical strength and creep) and more wear resistance, And the carbon-fiber reinforced plastic has 3.5 times the thermal conductivity of the unreinforced PEEK plastic and dissipates heat faster from the bearing surface.
Second, PEEK specifications: the following units are mm (mm)
PEEK bar: Diameter 3 ~ 260×1000 (3000 can be customized according to requirements) (if not above specifications, our company can supply product size, length and width specifications can be zero cut)
PEEK board
Model and color of PEEK board:
1, PEEK5600G (brown gray/earth yellow) using pure polyether ether ketone resin as raw material manufacturing, in all PEEK levels of good toughness, good impact resistance. PEEK can be sterilized by convenient disinfection methods (steam, drying heat, ethanol and Y-ray), and the raw materials of PEEK meet the requirements of the European Union and the United States FDA for food suitability. These characteristics make it very popular in the medical, pharmaceutical and food processing industries.
2, PEEK5600LF30 (black) add PTFE, graphite and carbon fiber results, so that PEEK-5600LF30 become bearing grade plastic. Its superior friction properties (low friction coefficient, wear resistance, high peak pressure limit) make this grade an ideal material for friction applications.
3, PEEK5600GF30 (brown gray) The material filled with 30% glass fiber reinforced plastic, compared with PEEK5600G has better rigidity and creep resistance, and better dimensional stability, the manufacturing of structural parts is ideal. It can withstand fixed load for a long time at high temperature. If the PEEK-5600GF30 is used as a sliding part, its adaptability should be carefully checked because the glass fiber scratches the mating surface.
4, PEEK5600CF30 (black) The material filled with 30% carbon fiber reinforced, has better mechanical properties than PEeK-5600GF30 (higher elastic modulus, mechanical strength and creep) and more wear resistance, and carbon fiber reinforced plastic than the unreinforced PEEK plastic has 3.5 times the thermal conductivity and faster heat dissipation from the bearing surface.
Three, PEEK specifications: the following units are mm (mm)
PEEK sheet: Extrusion width 1250mm and below the size of sheet (3000 can be customized according to requirements)
PEEK tube
PEEK tube type and color:
1, PEEK5600G (brown gray/earth yellow) using pure polyether ether ketone resin as raw material manufacturing, in all PEEK levels of good toughness, good impact resistance. PEEK can be sterilized by convenient disinfection methods (steam, drying heat, ethanol and Y-ray), and the raw materials of PEEK meet the requirements of the European Union and the United States FDA for food suitability. These characteristics make it very popular in the medical, pharmaceutical and food processing industries.
2, PEEK5600LF30 (black) add PTFE, graphite and carbon fiber results, so that PEEK-5600LF30 become bearing grade plastic. Its superior friction properties (low friction coefficient, wear resistance, high peak pressure limit) make this grade an ideal material for friction applications.
3, PEEK5600GF30 (brown gray) The material filled with 30% glass fiber reinforced plastic, compared with PEEK5600G has better rigidity and creep resistance, and better dimensional stability, the manufacturing of structural parts is ideal. It can withstand fixed load for a long time at high temperature. If the PEEK-5600GF30 is used as a sliding part, its adaptability should be carefully checked because the glass fiber scratches the mating surface.
4, PEEK5600CF30 (black) The material filled with 30% carbon fiber reinforced, has better mechanical properties than PEeK-5600GF30 (higher elastic modulus, mechanical strength and creep) and more wear resistance, and carbon fiber reinforced plastic than the unreinforced PEEK plastic has 3.5 times the thermal conductivity and faster heat dissipation from the bearing surface.
Specifications:
Dia 2mm -600mm
PEEK heat shrink tubes provide an ideal protection solution for sensitive components and some high-demand connectors. They can be used in harsh environments such as oil and gas environments, and protect electronic components from wear, high pressure, corrosion, chemical erosion, moisture, or electronic interference. It can be used with PEEK insulated cables instead of traditional fluoroplastic solutions and has an extremely wide operating temperature range.
Shrinkage temperature: 626℉/330℃-680℉/360℃
Operating temperature: 500℉/260℃
Restored wall thickness range:
0.1mm (0.004in)-0.23mm (0.004in)
Features:
Resistant to wear and tear,
• Anti-radiation linearity
High temperature resistant,
• Can adhere to metal surfaces
• Extend the life of protected objects
• Available in a variety of colors
Key performance:
Shrinkage to form a full-size protective layer can effectively protect the object from wear, extreme temperature conditions, high voltage and dielectric interference.
Applications: aerospace, nuclear power, military, automobile manufacturing, electrical and electronic, medical equipment, etc
Typical applications:
â—† Insulation protection of electronic components
â—† Protection of medical device parts
â—† Encapsulation and insulation of wire and cable
â—† Protective sheath can provide excellent wear resistance
â—† mandrel cladding
Product size:
â—† Can be used to recognize a variety of colors
â—† Length can be customized
â—† Consistent shrinkage ratio
PEEK various processing parts
Peek film ,PEEK Sheet, PEEK rod, PEEK tube, PEEK processed parts
Mianyang Prochema Commercial Co.,Ltd. , https://www.gustek.com